Starting a New Rod

I finished sanding the epoxy and enamel off my 7’ 9” 2/3 wt. and also picked out the hardware that I’m going to use.
 

Attachments

  • IMG_1063.jpeg
    IMG_1063.jpeg
    286.8 KB · Views: 126
  • IMG_1064.jpeg
    IMG_1064.jpeg
    315.4 KB · Views: 94
  • IMG_1065.jpeg
    IMG_1065.jpeg
    295.4 KB · Views: 95
i just saw this post, nice work on the quad!
i have a pre-60's Carlson 7 1/2' 5 wt.
posting a pic to show the nickel silver slide band hardware and the square handle.

IMG_4280.JPG
 
Looks amazing so far , can’t wait to see it finished.
Thanks, I was pleased on how the 7’9” turned out and the numbers are on mark when I mic’d it. The 9’ 4wt I’m pleased with the numbers as well (still sanding the butt section). But I re-calculated the numbers after I thought the Butt section would be too soft for what I wanted but it maybe too stiff now but we shall see.
 
It has been awhile since I worked on some rods but with some good results for the wife (Amy). I pulled out the blonde 7’9 4wt and cut it to length (measured twice and cut once 😁). I don’t know if I’m going to use one of the 3 color combinations or just go clear with red tip. But if someone has a comment let me know. I know bad pic and varnish. The final trim wraps will be only 5 turns. Joe E
 

Attachments

  • IMG_0109.png
    IMG_0109.png
    916.3 KB · Views: 67
I had the chance to do some rod work today—crowning the ferrules and turning down the blank for a perfect fit. Hopefully, I can get it wrapped and varnished over the next two weekends. I do have to do a touch up the crowning before I glue them tomorrow The combination of blonde bamboo and nickel silver hardware looks great IMO even though I don’t make that many blonde rods. I’ve settled on a thread color and will need to finalize that soon.
 

Attachments

  • IMG_0231.jpeg
    IMG_0231.jpeg
    487.2 KB · Views: 45
  • IMG_0232.jpeg
    IMG_0232.jpeg
    499.2 KB · Views: 44
As a dyed in the wool H.L Leonard fan, nothing stirs my heart more than blond bamboo and red wraps...

Nice work Joe!!
 
  • Like
Reactions: CRB
I had the opportunity to finish crowning the ferrules on the Hex. After cutting the two quads, I measured to determine the ferrule sizes I needed and ordered step-down ferrules to be broached. I was fortunate to speak with a Quad maker who helped answer a few questions, and I’m truly grateful for their guidance. I wasn’t looking for trade secrets I was just trying to minimize mistakes, especially since ferrules cost $70 per set.

For some reason, information on Hex rods is readily available, but when it comes to Quads, it’s much harder to find. Fortunately, there are still a few generous individuals willing to help. But if not I will figure it out 😁. Joe E
 
I had the opportunity to finish crowning the ferrules on the Hex. After cutting the two quads, I measured to determine the ferrule sizes I needed and ordered step-down ferrules to be broached. I was fortunate to speak with a Quad maker who helped answer a few questions, and I’m truly grateful for their guidance. I wasn’t looking for trade secrets I was just trying to minimize mistakes, especially since ferrules cost $70 per set.

For some reason, information on Hex rods is readily available, but when it comes to Quads, it’s much harder to find. Fortunately, there are still a few generous individuals willing to help. But if not I will figure it out 😁. Joe E
 
I ran into some medical issues this year. But should be good now. Daughter’s getting married in December and the wife has been on me to take it easy. But my friend of 40 years is retiring so he get 2 special gifts 😄. The blonde is a hex 7’9” 4 wt and the quad is a 7’9” 3 wt. the 4 is my favorite dry fly rod and the 3 wt is my favorite midge rod. I’ll let him fish them for a month then I will buff them out.
 

Attachments

  • IMG_0325.jpeg
    IMG_0325.jpeg
    368.2 KB · Views: 1
Back
Top