Rod Repair

steve98

Active member
Joined
Sep 9, 2006
Messages
305
Hello all, I came in possession of a Very Old L.E. Geischen bamboo fly rod.
One of the mid ferrules is loose where the bamboo is inserted to it.
Any suggestions on how to fix this?
Maybe some kind of epoxy that would work its way between the inside wall of the ferrule and the outside wall of the bamboo or maybe just a drop or two of Super Glue?
Thank You,

Steve 98
 
If the ferrules fit tight and are in good condition then pull the ferrule off. The are more than likely stepdown ferrules so Just watch it may be pinned and you will need to remove the pin before you start pulling. Don’t pull with pliers you could damage the ferrule. Glue back on with 5 minute epoxy. Male or female ferrule? if you post a picture it may help me confirm or make another suggestion.
 
Hello all, I came in possession of a Very Old L.E. Geischen bamboo fly rod.
One of the mid ferrules is loose where the bamboo is inserted to it.
Any suggestions on how to fix this?
Maybe some kind of epoxy that would work its way between the inside wall of the ferrule and the outside wall of the bamboo or maybe just a drop or two of Super Glue?
Thank You,

Steve 98

The best bet is to remove the loose ferrule completely, clean & re-glue and there are a lot of option and opinions on what glue. Doing anything less will cause issues down the road. Also forget super glues.

IF the ferrule is glued & pinned in place, removal is far from impossible but you must remove the pin to remove the ferrule. You can fabricate a very small pin punch from a finishing nail with a Dremel tool.

A fine center punch will work in a pinch, but will probably leave a mark on the end of the pin. Once you push the pin out a little bit, you can pull it out the rest of the way with smooth jawed pliers.

BTW - When you re-glue a pinned ferrule, you WILL have to realign the hole through the ferrule & the bamboo IF you want to replace the pin.

In the meantime, peruse this thread:


Good luck!
 
The best bet is to remove the loose ferrule completely, clean & re-glue and there are a lot of option and opinions on what glue. Doing anything less will cause issues down the road. Also forget super glues.

IF the ferrule is glued & pinned in place, removal is far from impossible but you must remove the pin to remove the ferrule. You can fabricate a very small pin punch from a finishing nail with a Dremel tool.

A fine center punch will work in a pinch, but will probably leave a mark on the end of the pin. Once you push the pin out a little bit, you can pull it out the rest of the way with smooth jawed pliers.

BTW - When you re-glue a pinned ferrule, you WILL have to realign the hole through the ferrule & the bamboo IF you want to replace the pin.

In the meantime, peruse this thread:


Good luck!
Ty Bam I do believe the original was glued and pinned. Removing the pin will definitely not be easy.
But if I do successfully remove the pin and the ferule , then what type of adhesive?
 
Ty Bam I do believe the original was glued and pinned. Removing the pin will definitely not be easy.
But if I do successfully remove the pin and the ferule , then what type of adhesive?

Read the link I provided:


There are LOTS of glue opinion from folks way more experienced than me, but the consensus seems to be a bunch of options other than 5-minute epoxy or super glue.
 
Hello all, I came in possession of a Very Old L.E. Geischen bamboo fly rod.
One of the mid ferrules is loose where the bamboo is inserted to it.
Any suggestions on how to fix this?
Maybe some kind of epoxy that would work its way between the inside wall of the ferrule and the outside wall of the bamboo or maybe just a drop or two of Super Glue?
Thank You,

Steve 98

Super glue is almost never the right choice for anything rod building related.
 
That will work! I have used epoxy on over 30 plus rods and only had one issue and I don’t believe it was the epoxy’s fault.
 
Ty Bam I do believe the original was glued and pinned. Removing the pin will definitely not be easy.
But if I do successfully remove the pin and the ferule , then what type of adhesive?

There's instructions on how to hammer the pin in deeper so you can slide the ferrule off. I bought a beater rod to learn some things on and this is something I need to do but haven't tried yet.
 
There's instructions on how to hammer the pin in deeper so you can slide the ferrule off. I bought a beater rod to learn some things on and this is something I need to do but haven't tried yet.

Some ferrules and even some cap & ring reelseat caps are pinned all the way through both ferrule walls & the bamboo.

They are easy to spot, remove and reinstall with a really small diameter pin punch, a VERY light hammer (think watchmakers tools), and a pair of fine tippled, smooth jaw long nose pliers.

You just have to be careful and not flatten the walls of the ferrule when extraction or replacing the pin. I have a simple wooden jig I made by drilling proper ferrule sized holes through a piece of wood then cutting the piece of wood in half so each half has half a hole.

Squeeze the halves together and use it to pull OFF ferrules. Drill a hole in one half where a pin is located and lay the ferrule in the half circle while you punch OUT or punch a pin BACK into the ferrule.
 
Once I've re-epoxy , then what is the purpose of the pin?
Thinking I will not need to reinstall.
 
FYI it is a step down Ferrule with two different Inside diameters from one end to the other,as is the bamboo shaft itself. The ferrule when installed becomes a Male .
 
Yes! Depending on the maker and age of the rod, I know, but it depends on the taper if it is a standard step down ferrule or true step down ferrule (example 13/64th to a 12/64th or 13/64th to 13/64th) too much to put in the post but you will need to mic both ends of the rod sections and the ferrules themselves. It is not difficult. PM me I can send you a dial caliper if you don’t have one and my phone number to walk you through it. I order all my ferrules from Dave at Rush River Rods good ferrules at a good price . Let me know Joe E
 
Back
Top