Multi nymph rig

Tabasco-Joe

Active member
Joined
Jan 24, 2022
Messages
243
City
SEPA
Looking for suggestions on mutli nymph leader setups. I was thinking of using about 4 feet of 3x and then 4 feet of 4x to the first fly. Blood not and first fly off tag. Then 18 inches to next blood knot and again fly off tag. Then 18 inches to last fly. Probably use a ring between 3x and 4x leader sections. Any suggestions?
 
I'll give you a Frankenstein nymph rig leader formula I use and you'll hate me for it 🤣

I'll take a tapered leader and cut it about 3 ft long. I put a tippet ring at the end of it. Off of that, I'll run a couple of feet of 3x to my first fly, 18 to 20 in of 4x to my second fly and do the same if I decide to run a third. I also run them in the reverse weight that most people find conventional and tie them eye to eye.

From The flyline to the tippet ring, that's 3 ft of adjustability with the indicator. In really deep water, it might be 9 or 10 ft to my bottom fly. In shallow water, move the indicator near the tippet ring and cut off the bottom fly.

When it's 10 ft from the indicator to the bottom fly and there's three on there.... Absolute nightmare to cast. I've gotten at least a dozen people on here to try throwing that rig and I think they all hate me for having them do it 🤣🤣
 
Looking for suggestions on mutli nymph leader setups. I was thinking of using about 4 feet of 3x and then 4 feet of 4x to the first fly. Blood not and first fly off tag. Then 18 inches to next blood knot and again fly off tag. Then 18 inches to last fly. Probably use a ring between 3x and 4x leader sections. Any suggestions?
You are on the right track but I would use a shortened leader as a butt section like Kray suggests. That will make for a better location to attach the indicator and will allow better mending of the leader above the indi. you can use strait 15lb or 20lb as a butt too. Taper doesn't really matter for this application.

I often run 3x for everything below the butt section and tie my flies off the leader using 4x tied to tippet rings or dropper loops. If I'm fishing small flies I'll step down to 4x like you are thinking and then use 5x for my droppers. I don't like using knot tags as my droppers, I prefer to have my flies on one size smaller tippet so that if they snag something I'm less likely to break off more than just one fly.

Personally, I usually run a drop shot set up. If not a pure drop shot then one fly off a tag above the weight, the weight pinched onto a knot tag (so it ca slide off if snagged) then the bottom fly trailing the weight.

I never tie my flies off of the bend of the previous fly on indicator rigs.
 
You are on the right track but I would use a shortened leader as a butt section like Kray suggests. That will make for a better location to attach the indicator and will allow better mending of the leader above the indi. you can use strait 15lb or 20lb as a butt too. Taper doesn't really matter for this application.

I often run 3x for everything below the butt section and tie my flies off the leader using 4x tied to tippet rings or dropper loops. If I'm fishing small flies I'll step down to 4x like you are thinking and then use 5x for my droppers. I don't like using knot tags as my droppers, I prefer to have my flies on one size smaller tippet so that if they snag something I'm less likely to break off more than just one fly.

Personally, I usually run a drop shot set up. If not a pure drop shot then one fly off a tag above the weight, the weight pinched onto a knot tag (so it ca slide off if snagged) then the bottom fly trailing the weight.

I never tie my flies off of the bend of the previous fly on indicator rigs.
I do a similar setup. 4' of .020 maxima to 1' of .013 maxima as my leader butt, then level tippet from there. Usually 4x with 5 or 6x droppers and I like to drop shot but sometimes I get lazy and just fish one fly with the shot above it.

OP check out Gary Borger's unibody leader.

 
When it's 10 ft from the indicator to the bottom fly and there's three on there.... Absolute nightmare to cast. I've gotten at least a dozen people on here to try throwing that rig and I think they all hate me for having them do it 🤣🤣
Ugh. I could only throw that two ways: out or away.
 
You are on the right track but I would use a shortened leader as a butt section like Kray suggests. That will make for a better location to attach the indicator and will allow better mending of the leader above the indi. you can use strait 15lb or 20lb as a butt too. Taper doesn't really matter for this application.

I often run 3x for everything below the butt section and tie my flies off the leader using 4x tied to tippet rings or dropper loops. If I'm fishing small flies I'll step down to 4x like you are thinking and then use 5x for my droppers. I don't like using knot tags as my droppers, I prefer to have my flies on one size smaller tippet so that if they snag something I'm less likely to break off more than just one fly.

Personally, I usually run a drop shot set up. If not a pure drop shot then one fly off a tag above the weight, the weight pinched onto a knot tag (so it ca slide off if snagged) then the bottom fly trailing the weight.

I never tie my flies off of the bend of the previous fly on indicator rigs.
Dave Rothrock's method. Excellent video with explanation

 
An add on question, when I tie a blood knot I get two tags. Any reason I couldn't just let the unused tag go untrimed to use once the first tag is too short to retie?
 
An add on question, when I tie a blood knot I get two tags. Any reason I couldn't just let the unused tag go untrimed to use once the first tag is too short to retie?
I’ve done that exact thing and had success but I admit I only started using the tags to tie on my droppers in the past 4 months. Previously I was tying to the hook bend of the fly above and also felt that I was missing fish that were encountering the tippet just like Dave says in his video.
 
I’ve done that exact thing and had success but I admit I only started using the tags to tie on my droppers in the past 4 months. Previously I was tying to the hook bend of the fly above and also felt that I was missing fish that were encountering the tippet just like Dave says in his video.
It seems to be a trade off from my experience, if I attach the top fly on a tag, I catch more fish than if the bottom fly is off the first fly hook bend, but I also get more and worse line tangles.
 
Similar but different, since I don't fish weighted nymphs. I just cinch knot a piece of 4x onto my leader and butt it against the next segment's blood knot and tie the dropper there. Stiffer mono helps it stand away from the leader and doesn't mean I ahve to tie off the eye or the bend.

I can, and have, used the tag end of the blood knots but eventually that gets cut down to nothing.
 
Back
Top